Firmware Upgrade
First step:
Check BPI can work.
Using cfgedit.ext to edit cm-NmAccess.cfg.
Change BPI = 0 to BPI = 1.
Don't need add manufature's CVC.
Remeber put the right key (public and private).
mainMenu> shell
Exiting to shell. Type "exit" to return back to CLI
BusyBox v1.19.2 (2012-04-23 10:16:56 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.
# ifconfig
eth0 Link encap:Ethernet HWaddr AA:BB:CC:00:11:22
inet6 addr: fe80::a8bb:ccff:fe00:1122/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:1740 errors:0 dropped:0 overruns:0 frame:0
TX packets:1744 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:104864 (102.4 KiB) TX bytes:1826384 (1.7 MiB)
Base address:0xe000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
# testmode
*************************************
Starting Test Mode
*************************************
Installing Logger service... DONE
Installing GP-Timer service... DONE
Installing VLYNQ kernel module... TI Logger: Init complete
[INFO] [COMMON_COMPONENTS.GPTIMER(pid=171)]: Initialized successfully, timer tick 10ms
DONE
Installing SOC Interface kernel module... PAL_cppi4Init : domain is 0, cfg ptr is 0x00000000
PAL_cppi4Init : Object Address is 0x80490EF4
RX Init CPPI: open free descriptor queue
RX Init CPPI: allocate descriptors
init_cppi_rx: Allocate descriptors to the embedded free queues
RX Init CPPI: Fill free discriptor queue
RX Init CPPI: Set DMA channel
init_cppi_rx: Call PAL_cppi4RxChOpen channel=12, REF_CNT=1 BUF COUNT=512
RX Init CPPI: Init accumulator
RX Init RX CPPI pass
TX Init CPPI: open free descriptor queue
TX Init CPPI: allocate descriptors
init_cppi_tx: Allocate descriptors to the embedded free queues
TX Init CPPI: Fill free discriptor queue
TX Init CPPI: Create CPGMAC TX handler
TX Init CPPI: open mpeg TX channel
TX Init CPPI pass
WQ Init CPPI: open queue descriptor queue
WQ Init pass
MPEG driver initialization complete.
DONE
Installing DOCSIS bridge kernel module... DONE
Installing CNI kernel module... __gmac_dev_event *************************************
event 16 name cni0
__gmac_dev_event *************************************
event 5 name cni0
PAL_cppi4Init : domain is 0, cfg ptr is 0x00000000
PAL_cppi4Init : Object Address is 0x80490EF4
DONE
Initializing DOCSIS driver... [ERROR] [COMMON_COMPONENTS.GIM(pid=186)]: nid=4096: Failed to send Gim message
DONE
Installing DOCSIS Manager kernel module... PAL_cppi4Init : domain is 0, cfg ptr is 0x00000000
PAL_cppi4Init : Object Address is 0x80490EF4
Entered HAL_DocsisCppiInit
PAL_cppi4Init : domain is 1, cfg ptr is 0x7F23B5A8
PAL_cppi4Init : Object Address is 0x804927D4
PAL_cppi4Init : Before MEM Test
PAL_cppi4Init : Before QMGR Init
PAL_cppi4Init : QMGR [0] Init ...
PAL_cppi4Init : QMGR [1] Init ...
Off chip memory allocated: 32768
QMgr Init: buffer after alignment: 86e30000
PAL_cppi4BufPoolDirectInit : Pool[ 0] is at 0x01040000 of 0x00008000 size
DONE
Installing Interrupt handler kernel module... DONE
Initializing HAL Command Mailbox application... DONE
Initializing HAL Event Mailbox application... DONE
Initializing Interrupt handler application... DONE
Initializing Tuner manager application... DONE
**** Test mode initialization completed ****
>>>
Console, CLI version 1.0.0.5
Type 'help' for list of commands
mainMenu> docsis
docsis> ?
Console Commands for this level:
version - prints docsis version.
phystatus - <0 1 2 3 >;Display status of PHY given channels.
tuner - <Master -1 / Slave - 0> <Freq>;Program the WB tuner to frequency (MHz).
statustuner - Tuner configuration data. In WBT – regular status. In NBT – status for all tuner.
scan - stop/start scanning.
cerreset - <Rx channel 0,1,2,3> Reset CER counter.
cmstatus - Print CM status.
listDocsisModules - Show moudles list and indicates set/unset for each.
configDocsisModule - set/unset a module (module_id, 1/0).
testDsLoss - Simulate Ds signal loss (usPort, sec, recovTech).
Show - go to Show Menu.
Production - go to Production Menu.
Certification - go to Certification Menu.
General - go to General Menu.
Atp - go to Atp Menu.
Fw - go to Fw Menu.
Qos - go to Qos Menu.
Debug - go to Debug Menu.
Dsid - go to Dsid Menu.
Pp - go to Packet Processor Menu.
Psm - go to Power save mode Menu.
help - Display menu commands.
shortcuts - Display key shortcuts help.
exit - Exit this sub-menu, go to previous menu.
top - Go to mainMenu.
shell - Open shell command line, CLI in background.
quit - Quit and terminate CLI.
reboot - Reboot the system.
docsis> Production
ProductionMenu Entry Function
Production> ?
Console Commands for this level:
dir - List the available modem software versions.
dl - <sector number> <srvIPv4> <Interface Name> <name> <secured:0,1>;Download <name> form <srvIP> to <sec>.
erase - <sector number>;Erase <sector number>.
prodset - Set production params.
prodshow - Show production parameters.
setdef - <sector:1,2>;Set <sector> as default modem software.
rev1set - <Is Default STDMA:0/1>; Set Rev1 default to STDMA(1) or ATDMA(0).
rev1get - Shows Rev1 default: STDMA(1) or ATDMA(0).
boardConfigs - Print avaliable board configurations.
currentBoardConfig - Print current board configuration.
Calibration - go to Calibration.
Test - go to Test Menu.
Prodcertification - go to Certification.
help - Display menu commands.
shortcuts - Display key shortcuts help.
exit - Exit this sub-menu, go to previous menu.
top - Go to mainMenu.
shell - Open shell command line, CLI in background.
quit - Quit and terminate CLI.
reboot - Reboot the system.
Production> Prodcertification
ProdcertificationMenu Entry Function
Prodcertification> ?
Console Commands for this level:
cert - <server IP> <certificate file name> <key file name>;Download certificate..
help - Display menu commands.
shortcuts - Display key shortcuts help.
exit - Exit this sub-menu, go to previous menu.
top - Go to mainMenu.
shell - Open shell command line, CLI in background.
quit - Quit and terminate CLI.
reboot - Reboot the system.
Prodcertification> cert EU_cert_78e400c32a00.cer EU_cert_78e400c32a00.key
Cer file name EU_cert_78e400c32a00.cer
, private key file name EU_cert_78e400c32a00.key
// Make sure those key under below is right.
// This is where the private key is.
# ls -la
lrwxrwxrwx 1 36 mfg_key_pub.bin -> /etc/docsis/security/mfg_key_pub.bin
lrwxrwxrwx 1 33 cm_cert.cer -> download/ND_cert_78e400c327a3.cer
lrwxrwxrwx 1 33 mfg_cert.cer -> /etc/docsis/security/mfg_cert.cer
lrwxrwxrwx 1 33 cm_key_prv.bin -> download/ND_cert_78e400c327a3.key
drwxr-xr-x 2 0 download
lrwxrwxrwx 1 37 root_pub_key.bin -> /etc/docsis/security/root_pub_key.bin
drwxr-xr-x 5 0 ..
drwxr-xr-x 3 0 .
// This is where the public key is.
/etc/docsis/security
# ls -al
-rwxr-xr-x 1 837 euro_mfg_cert.cer
-rwxr-xr-x 1 270 euro_root_pub_key.bin
-rwxr-xr-x 1 873 mfg_cert.cer
-rwxr-xr-x 1 270 root_pub_key.bin
//Then check CASA status.
Connect to CASA, then type "show cable modem".
If you see our modem is online(pt).
That mean BPI work now.
//If BPI online thne I got 50% point.
That is mean our key is alright.
// Second step Signed tool
Please use VMware (Signed_image_can_work) to sign image.
//Change configuration file
If CVC code too long, please separate it.
Add Manufacturer's CVC(32) [len=254].
Add Manufacturer's CVC(32) [len=254].
Add Manufacturer's CVC(32) [len=241].
Add Software Upgrade Filename (9)
Make sure Privacy Enable(29) = 1
Then enjoy firmware upgrade now.
2012年4月26日 星期四
訂閱：
張貼留言 (Atom)
0 意見:
張貼留言